This recipe combines 300 g tagliatelle, 200 g Chinese cabbage and 200 g minced beef with garlic, soy sauce and sesame. It makes 4 servings in about 35 minutes. Use the Thermomix® for chopping and cooking the pasta, and a separate frying pan for the beef and cabbage.

Chop the vegetables first
Chop the parsley leaves for 3 seconds at speed 7 and set them aside for serving. Put the 30 g olive oil into the frying pan. Chop the peeled garlic clove for 3 seconds at speed 8, then transfer it to the same pan.
Wash and trim the Chinese cabbage. Cut it into large pieces and chop for 3 seconds at speed 4, then set it aside. Keep the reserved parsley separate; it goes on the finished dish.
Cook the pasta in reverse mode
Heat 1200 g water for 10 minutes at 100 °C and speed 1. Add the 300 g tagliatelle and 1 tsp salt. Use the cooking time on the pasta packet, with the Thermomix® set to 90 °C, reverse, speed 1.
Use the frying pan alongside the Thermomix®
While the pasta cooks, fry the minced beef in the pan with the oil and garlic, breaking it up and cooking it through. Add the reserved cabbage, 20 g soy sauce and 1 tsp sesame seeds, then continue cooking over medium heat.

Combine and finish
Drain the pasta in a suitable colander and add it to the pan. Toss everything together briefly and check the seasoning. The separate salt and pepper at the end are for seasoning to taste; the measured teaspoon of salt belongs in the pasta water. Sprinkle the chopped parsley over the finished dish.
Serve immediately, with spelt baguette if desired. The recipe notes mention savoy cabbage as a variation; use Chinese cabbage for the measured base version.
Tagliatelle with Chinese Cabbage and Beef with the Thermomix®
Ingredients 0 / 12 ✓
- 1/2 bunch parsley
- 30 g olive oil
- 1 garlic clove
- 200 g Chinese cabbage
- 1200 g water
- 300 g tagliatelle ribbon pasta
- 1 tsp salt for cooking the pasta
- 200 g minced beef
- 20 g soy sauce
- 1 tsp sesame seeds
- salt to taste, for the finished dish
- freshly ground pepper to taste
Instructions 0 / 7
-
1
Chop the parsley.
Wash the parsley and shake dry. Put the leaves into the mixing bowl, chop for 3 seconds/speed 7 and set aside.
- 1/2 bunch parsley
-
2
Prepare the oil and garlic.
Put the olive oil into a frying pan. Peel the garlic, put it into the mixing bowl and chop for 3 seconds/speed 8. Transfer the garlic to the frying pan.
- 30 g olive oil
- 1 garlic clove
-
3
Chop the Chinese cabbage.
Wash and trim the Chinese cabbage, cut it into large pieces and put it into the mixing bowl. Chop for 3 seconds/speed 4 and set aside.
- 200 g Chinese cabbage
-
4
Heat the pasta water.
Put the water into the mixing bowl and heat for 10 minutes/100 °C/speed 1.
- 1200 g water
-
5
Cook the pasta.
Add the tagliatelle and the measured 1 tsp salt. Cook for the time stated on the pasta packet/90 °C/reverse/speed 1.
- 300 g tagliatelle
- 1 tsp salt
-
6
Cook the beef and cabbage in the pan.
Meanwhile, add the minced beef to the frying pan with the oil and garlic. Fry, breaking it up, until cooked through. Add the reserved Chinese cabbage, soy sauce and sesame seeds and continue cooking over medium heat.
- 200 g minced beef
- 200 g Chinese cabbage
- 20 g soy sauce
- 1 tsp sesame seeds
-
7
Drain, combine and serve.
Drain the pasta in a suitable colander and add it to the frying pan. Toss together briefly, then season to taste with the additional salt and freshly ground pepper. Serve sprinkled with the reserved parsley.
- 300 g tagliatelle
- salt
- freshly ground pepper
- 1/2 bunch parsley
Variation: The original notes suggest savoy cabbage instead of Chinese cabbage. The measured base recipe uses Chinese cabbage.